Euro Pro Iron EP8001 User Manual

EP8001  
STEAM GENERATOR IRON  
PROFESSIONAL TYPE IRONING SYSTEM FOR  
HOUSEHOLD USE  
USE AND CARE INSTRUCTION MANUAL  
READ BEFORE USING THE IRONING SYSTEM  
CONGRATULATIONS! YOU ARE THE OWNER OF THE ULTIMATE IN MODERN  
IRONING AND PRESSING EQUIPMENT. FOR YOUR SAFETY AND TO FULLY ENJOY  
THE ADVANTAGES OF YOUR APPLIANCE, PLEASE TAKE A FEW MINUTES TO  
READ ALL THE IMPORTANT SAFEGUARDS AND “USE & CARE INSTRUCTIONS”.  
KEEP THIS MANUAL HANDY FOR EASY REFERENCE. PLEASE REVIEW THE  
PRODUCT WARRANTY AND MAIL THE OWNER REGISTRATION FORM  
EURO-PRO Operating LLC  
94 MAIN MILL STREET, DOOR 16  
PLATTSBURGH, NY 12901  
USA  
EURO-PRO Operating LLC  
4400 BOIS FRANC  
ST. LAURENT, QUEBEC H4S 1A7  
CANADA  
 
Even if you have used a steam generator iron before, please read all instructions and safeguards  
in the Use and Care Instruction Book. In addition, please note the following user tips:  
USING STEAM  
PLEASE NOTE: Steam performance improves after the first 6-8 hours of usage. The steam  
power increases and initial condensation at maximum temperature is reduced.  
1. Make sure the temperature setting of the iron is within the steam range on the temperature  
selector.  
2. Turn power on for iron and steam generator. Before starting to use steam, make sure the  
Steam Ready Light (2) is “ON”, indicating that steam is available.  
NOTE: Trying to use steam before the Steam Ready Light (2) is “ON” can cause water  
drops in the stem coming out of the iron.  
CLEARING THE INITIAL CONDENSATION:  
3. Clear the initial condensation by pressing the Steam Button (C) up to 3 seconds. Repeat if  
necessary.  
IMPORTANT NOTE:  
4. While using the ironing system, if steam has not been released for more than  
approximately 5 minutes, the hose has cooled and any steam remaining in the hose from  
the last use might condense. Clear this condensation by pressing Steam Button (C) before  
proceeding to use the iron.  
2
 
MODEL EP8001  
STEAM GENERATOR IRON  
7
5
6
9
8
A. Iron Heat Indicator Light  
B. Temperature Dial  
C. Steam Button  
1. Safety/Filler Cap  
2. Steam Ready Light (amber)  
3. Steam ON/OFF Rocker Switch  
4. Iron ON/OFF Rocker Switch  
5. Water Tank/Steam Generator  
6. Iron Rest  
7. Steam Hose  
8. Power Cord  
9. Funnel  
D. Continuous Steam Button Lock  
Technical features:  
Total power: 1500/1780W, 110/120V., 60Hz  
Water capacity: 1liter/33.8 US fl. oz.  
Working pressure: 3,5bar  
3
 
STEAM GENERATOR  
IMPORTANT SUPPLEMENTARY USER INFORMATION  
Read all instructions before using the Steam Generator Iron and follow all instructions and  
safeguards carefully.  
IMPORTANT NOTES ON THE USE OF A STEAM GENERATOR:  
DO NOT OPEN THE SAFETY/FILLER CAP (1) BEFORE ALL THE REMAINING STEAM IS  
RELEASED (EMPTIED) FROM THE WATER TANK/STEAM GENERATOR (5) AND THE  
GENERATOR HAS COOLED. TO RELEASE THE STEAM TURN THE STEAM ON/OFF  
ROCKER SWITCH (3) TO THE “OFF” POSITION. PUSH THESTEAM BUTTON (C) UNTIL NO  
MORE STEAM COMES OUT OF THE IRON, THEN OPEN SLOWLY THE SAFETY/FILLER  
CAP (1).  
1. A WORD ON WATER  
For best results we recommend using 100% demineralized/distilled water.  
The use of demineralized/distilled water will prolong the life of your generator and reduce the  
frequency of required generator cleaning, as well as the possibility of staining due to  
accumulated impurities.  
DO NOT USE WATER PROCESSED THROUGH A HOME WATER SOFTENING SYSTEM  
OR BOTTLED MINERAL WATER.  
If you choose to use regular tap water, make sure that the chloride (CL) level of your local water  
supply does not exceed 8mg/liter. In many areas, the chloride level exceeds 8mg/liter. Use of  
tap water with high chloride levels will adversely affect the life expectancy of your steam  
generator. Tap water can be mixed with demineralized/distilled water to lower the chloride level.  
For best results make sure to use the right proportions to bring the chloride level to 8mg/liter or  
less.  
2. DO NOT OVERFILL THE STEAM GENERATOR  
When empty, the water tank/steam generator (5) can be filled with 1 liter/33.8 US oz. of  
demineralized/distilled water. Do NOT overfill. Overfilling the tank can cause water drops  
coming out of the steam holes. See instructions on page 6.  
3. DO NOT CLOSE THE SAFETY/FILLING CAP (1) TOO TIGHTLY  
To close, turn the Safety/Filler Cap (1) clockwise until the point where you feel friction - do not  
close too tightly. The Safety/Filler Cap (1) includes a gasket which can be flattened and  
damaged if the cap is closed too tightly. If the gasket is damaged, steam may escape while  
the generator is used, even when the Safety/Filler Cap (1) is closed. If your Safety/Filler Cap  
(1) is damaged and steam is leaking, you may call Customer Service at 1 (800) 798-7398 to  
purchase a replacement Safety/Filler Cap (1).  
4. FOR BEST RESULTS DO NOT LEAVE HOT IRON RESTING IDLE ON IRON REST (6)  
FOR LONG PERIODS OF TIME  
The life-span of your EP8001 will be reduced if the iron is left idle at high temperatures for  
extended periods. If iron is not in use, reduce its temperature to the lowest temperature setting  
on the Temperature Dial (B).  
5. WARRANTED FOR REGULAR HOUEHOLD USE  
While the EP8001 is a professional type ironing system, it is intended for and warranted only  
for normal household use. Iron and/or steam generator should not be used for more than 15  
hours per week in approximately 3 hour intervals.  
4
 
INSTRUCTIONS FOR USE  
Your new Ironing System offers the ultimate in modern ironing. Read carefully all the important  
safeguards (page 1) and all the instructions in the user manual before using your Ironing  
System. Follow all the instructions.  
1. WARNINGS:  
Never leave the unit unattended while plugged in. Always disconnect from electrical power source.  
• You must always unplug (disconnect) the unit when you have finished using it and:  
A) Before opening the Safety/Filler Cap (1).  
B) Before any cleaning or maintenance.  
C) Before filling and emptying the water tank/steam generator (5).  
D) When you leave the room, even if only for a few minutes.  
• Always place the iron on the iron rest (6) when not in use.  
• Never use the ironing system if the iron or the steam generator have been dropped. To avoid risk of  
electric shock, do not disassemble or attempt to repair the ironing system. Return the unit to  
EURO-PRO Operating LLC. (see warranty) for examination, repair or replacement.  
• Do not stretch out the power cord (8) and/or steam hose (7) while ironing. Do not use the appliance if  
an power cord (8) and/or steam hose (7) is damaged. If the power cord (8) or steam hose (7) show  
signs of wear or damage, please return the unit to EURO-PRO Operating LLC (see warranty) for  
examination, repair or replacement.  
• Read the “IMPORTANT SAFEGUARDS” listed on page 1 and all special instructions and follow  
carefully.  
2. DRY IRONING:  
1. Place your steam generator on a solid flat surface.  
2. Plug in unit. Press the Iron ON/Off Rocker Switch (4) which lights up to indicate that the iron is “ON”.  
3. Set the Temperature Dial (B) according to the garment label or use the temperature setting table  
included in the user’s manual as a guide.  
4. The Iron Heat Indicator Light (A) will go on and will turn off when the iron has reached the desired  
temperature.  
5. You may iron without steam at any temperature setting.  
3. IRONING WITH STEAM:  
1. Plug the appliance into a 110/120 V electrical outlet.  
2. Press the Iron ON/Off Rocker Switch (4) to the “ON” position. Press the Steam ON/OFF Rocker  
Switch (3) to activate steam generator.  
3. When planning to use steam, make sure to set the Temperature Dial (B) in the area designated for  
use with steam. i.e. between the two “ ” and three “ ” dots on the Temperature Dial (B).  
(See temperature setting table included in the user’s manual as a guide.)  
4. The Steam Ready Light (2) will come on in 8-10 minutes indicating steam is available. The Steam  
Ready Light (2) will go on and off while the generator is in use.  
5. Press Steam Button (C) to activate the steam release.  
NOTE: Trying to use steam before the Steam Ready Light (2) is “ON” can cause water drops  
in the stem coming out of the iron.  
4. CONTINUOUS STEAM BUTTON:  
If you need a steady steam supply, press the Continuous Steam Button (D) down and then push it  
backwards to lock the Steam Button (C) in. To unlock, press the Continuous Steam Button (D) down  
again and push it forwards.  
NOTE: Before ironing, point iron away from table, press steam button (C) to clear initial condensation.  
WARNING: Never direct steam from the iron at yourself or another person. Special care must be  
taken when the iron is used in a vertical position. The steam is very hot and can cause burns.  
5
 
5. STEAM:  
IMPORTANT WARNING:  
DO NOT OPEN THE SAFETY/FILLER CAP (1) BEFORE ALL THE REMAINING STEAM IS  
RELEASED (EMPTIED) FROM THE WATER TANK/STEAM GENERATOR (5) AND THE  
GENERATOR HAS COOLED.  
A. TO EMPTY/RELEASE STEAM FROM THE GENERATOR:  
Steam ON/OFF  
Switch  
1. Press “Iron On/Off Rocker Switch (4) into the “ON” position.  
2. Press the “Steam On/Off Rocker Switch (3) into the “Off”  
Steam Ready  
position.  
Light  
3. Release all remaining steam in the steam generator by  
pressing the “Steam Button” (C) on the iron.  
4. Press the Iron ON/OFF Rocker Switch (4) into the “OFF”  
position.  
5. Unplug the appliance from the wall outlet. Allow it to cool a  
Iron ON/OFF  
minimum of 5 minutes. Make sure that both the Iron  
ON/OFF Rocker Switch (4) and the Steam ON/OFF Rocker  
Switch  
Switch (3) are in the “OFF” position.  
To unscrew the Safety/Filler Cap (1), push down slightly on the gray outside ring and turn the  
cap counterclockwise, slowly. If any steam continues to escape, STOP. Repeat instructions  
above for releasing steam from the generator.  
B. FILLING WATER TANK/STEAM GENERATOR (5) :  
1. Make sure that both Iron ON/OFF Rocker Switch (4) and Steam ON/OFF Rocker Switch (3)  
are in the “OFF” position.  
2. Make sure that your appliance is unplugged i.e. is not connected to an electrical power  
source.  
3. Make sure that any remaining steam in the Steam Generator has been released through  
the iron as described in Section “A” above.  
4. To unscrew the Safety/Filler Cap (1), push down and turn the cap counterclockwise,  
slowly. If any steam continues to escape, stop and release the steam through the iron  
as in Section “A” above.  
5. Put the Funnel (9) into the filling pipe, under the Safety/Filler Cap (1)  
6. Fill the tank with water (warm if possible), to the top of the filling pipe.  
7. Remove the Funnel (9) from the filling pipe. You will notice that the water level dropped to  
be approximately 2 inches below the top of the filling pipe.  
8. DO NOT ADD ANY MORE WATER NOW. The automatic filling system makes sure that  
when you follow the above instructions, the steam generator is full of water.  
9. Replace the Safety/Filler Cap (1) turning clockwise until you get friction. DO NOT CLOSE  
TOO TIGHTLY OR GASKET WILL BE FLATTENED.  
IMPORTANT NOTE:  
DO NOT ADD ANY MORE WATER TO THE TANK AFTER THE WATER LEVEL HAS  
DROPPED. (SEE #7 ABOVE.)  
ADDING MORE WATER TO THE TANK AT THIS POINT WILL CAUSE OVERFILLING AND  
RESULT IN WATER DROPS IN THE STEAM.  
6
 
C. WHEN TO REFILL THE WATER TANK/STEAM GENERATOR (5):  
For best results, refill water tank/steam generator (5) to maximum before every usage and  
when steam power is recognized lower while in use. Turn Iron ON/OFF Rocker Switch (4) and  
Steam ON/OFF Rocker Switch (3) to “OFF” position and release all steam from generator as  
described on page 6 Section A.  
D. TEMPERATURE SETTINGS:  
• Always read garment labels and follow directions.  
• For maximum efficiency, iron garments requiring the lowest temperature settings first as the  
iron heats up faster than it cools.  
• If there are no instructions included with the garment, we suggest that you follow the table  
above as a guide (except when any fabric has an applied finish, gloss, etc. where lower  
temperatures might be required).  
• Always iron blends (fabrics made of two or more types of fibers) using the heat setting  
appropriate for the fabric requiring the lowest temperature setting.  
6. IMPORTANT PRESSING TIPS:  
A. USE STEAM INTERMITTENTLY:  
Your Steam Generator Iron features a professional type iron with steam holes placed in the  
front of the iron soleplate. Correct ironing procedure involves steaming the fabric with the front  
end of the iron followed by pressing and drying with heat from the rear of the iron. For best  
results, garments should be dry after pressing to avoid re-wrinkling due to lingering dampness.  
Therefore, we recommend that you use steam as required, but not continuously.  
B. PRESSING DIFFICULT NATURAL FIBERS (I.E. 100% COTTON DRESS SHIRTS, ETC.):  
While your Steam Generator offers high quality professional type steam, some fabrics may  
require additional moisture for best results. You may want to press cotton shirts while still  
damp or spray with demineralized/distilled water, prior to ironing.  
7
 
C. DRY STEAM V.S. HUMID STEAM:  
Because steam is produced in a generator and not in the iron (as with regular household irons)  
you can select dry or humid steam. The temperature of the iron setting determines the type of  
steam. At high temperatures, the iron delivers very dry steam. Lower temperature settings  
(within steam range) offer humid steam.  
D. USER BENEFITS:  
For best pressing results, you have the flexibility to choose the type of steam and not only the  
iron temperature.  
A balance should be maintained between the humidity (low iron  
temperature) required to loosen fibers and the need for heat (higher iron temperature) to  
flatten/shape and dry the fibers.  
Instructions for specific iron temperature settings should be treated as guidelines only. We  
recommend that you experiment with each fabric. The EP8001 can produce humid steam at  
relatively low temperature settings where regular household irons would release water. Also,  
the very dry steam produced at high iron temperature setting (3 dots “ ”) can be used on  
some fabrics where normally the use of steam is prohibited.  
8
 
STORAGE/CLEANING AND MAINTENANCE  
STORAGE:  
• Always unplug the power cord from the wall outlet when not in use.  
• Always store in a dry place away from children’s reach.  
• Always drain the Water Tank/Steam Generator (5) before storing.  
• Always let your ironing system cool completely before putting away.  
• Do not allow the electrical cord and steam hose to touch hot surfaces.  
• Wrap the cord loosely around the ironing system when storing.  
CLEANING/MAINTENANCE:  
• The cord must be unplugged from the wall outlet before starting to clean any part of the  
appliance.  
• Make sure that the Iron and Steam Generator are COLD before starting to clean. Allow  
at least four (4) hours for the unit to cool after it has been used.  
• Make sure that all steam has been emptied (released from the steam generator) before  
opening the Safety/Filler Cap. (Follow instructions on page 6 Section A for releasing  
steam.)  
IRON:  
• Clean the steam iron only when it is cold.  
• Never immerse the steam iron in water or any other liquids.  
• Do not use scouring pads, abrasives or harsh cleaners.  
• Prepare a paste using mild scouring powder and a little water. Apply a small amount of  
the paste to the soleplate with a damp cloth. Rub the soiled area and then wipe clean  
with a clean damp cloth.  
• If using soleplate cleaners, make sure that you follow label instructions.  
• Use a soft cloth dampened with water and mild household detergent to wipe the outer  
shell of the iron.  
• Dry soleplate and thoroughly after cleaning.  
STEAM GENERATOR:  
We strongly recommend using demineralized/distilled water to insure optimum performance  
and maximize the life of your steam generator.  
If you are using demineralized/distilled water, the steam generator should be cleaned once  
every 6 to 12 months, depending on the frequency and duration of usage. If you use regular  
tap water, the steam generator should be cleaned once a month.  
1. Make sure that there is no steam remaining in the steam generator. Follow the  
instructions for emptying/releasing steam from the steam generator on page 6 Section A.  
2. Make sure that the steam generator is cold.  
3. Remove the Safety/Filler Cap (1), carefully following the instructions to make sure that the  
unit is cold by slowly turning the cap to allow any remaining steam to escape. If any  
steam is released, stop and follow instructions for emptying/releasing steam on page 6  
Section A.  
4. Fill the tank with water as per instructions on Page 6.  
5. Plug in the unit. Switch on the system by pressing the Iron ON/OFF Rocker Switch (4)  
and the Steam ON/OFF Rocker Switch (3). DO NOT LEAVE UNIT UNATTENDED.  
6. Allow a few minutes until the water starts to boil without the Safety/Filler Cap (1) on. DO  
NOT LEAVE UNIT UNATTENDED.  
7. Put the Iron ON/OFF Rocker Switch (4) and the Steam ON/OFF Rocker Switch (3) in the  
“OFF” position. Unplug the unit from the electrical outlet.  
8. Allow the unit to cool completely.  
9. Empty the water contained in the generator.  
10. YOUR STEAM GENERATOR IS NOW CLEAN.  
9
 
TROUBLESHOOTING  
Do not operate the ironing system with a damaged cord, plug or if the iron or any other part of  
the system has been dropped or damaged. To avoid the risk of electric shock, do not  
disassemble or attempt to repair the ironing system. Return the appliance to EURO-PRO  
Operating LLC (see Warranty) for examination and repair. Incorrect re-assembly or repair can  
cause a risk of electric shock or injury to persons when the ironing system is used.  
POSSIBLE CAUSES  
REMEDY  
PROBLEM  
1. Turn Steam ON/OFF Rocker  
Switch “ON” .  
No steam is released  
through the iron  
1. Steam ON/OFF Rocker Switch is  
not in the “ON” position.  
2. Fill with water as per instructions.  
2. Water Tank/Steam Generator is  
empty.  
3. Unit is not plugged in.  
4. Steam is not visible because the  
temperature of the soleplate is at  
maximum & room temperature is  
high.  
3. Make sure both Steam & Iron  
ON/OFF Rocker Switches are in  
the “OFF” position and plug unit  
in.  
4/5.The heating time for the generator  
is approximately 8-10 minutes .  
Watch for Steam Ready Light to  
come on indicating that steam is  
ready.  
5. Generator is NOT fully heated.  
1. Iron is not switched ON.  
2. Temperature is set at “Minimum”.  
1. Turn Iron ON/OFF Rocker Switch  
“ON” .  
The soleplate remains  
cold  
2. Turn the temperature dial to the  
appropriate setting.  
1. Soleplate temperature is too low  
to iron with steam.  
1. Turn the temperature dial to the  
marks between 2 and 3 dots. .  
Drops of water leak  
from the iron soleplate  
2. Generator is NOT fully heated.  
2. Wait for generator to be fully  
heated.  
1. Residue in water tank.  
2. Not using demineralized/distilled  
water.  
1. Clean steam generator as per  
instructions.  
2. Use demineralized/distilled water  
after cleaning the tank.  
Dirty or yellow steam is  
coming out of the iron  
1. Order new Safety/Filler Cap (1)  
from Customer Service at  
1 (800) 798-7398.  
1. Gasket is broken because  
Safety/Filler Cap (1) was closed  
too tightly or cap was opened  
while tank was full of steam and  
gasket broke.  
Steam leaking from cap  
1. Steam leaking/iron left hot and  
idle on the generator.  
1. Order new Safety/Filler Cap (1). Do  
not leave iron on iron rest (6) while  
hot for extended periods of time.  
Top getting yellow near  
Safety/Filler Cap  
1. Yellowing occurs with normal  
aging.  
Yellowing of generator  
Excessive yellowing  
1. Leaving iron idle on top of  
generator at high temperature for  
long periods of time.  
10  
 
Model EP8001  
LIMITED WARRANTY  
EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a  
period of ONE (1) year from the date of purchase when utilized for normal household use by the original  
purchaser only. The attached Warranty Registration Card which must be filled out and returned within 10 days  
of purchase. This is essential for your Warranty to be effective should any problem arise with this product.  
Should any defect covered by the terms of the limited warranty be discovered within ONE year, EURO-PRO  
Operating LLC will repair or replace any defective part provided the unit is returned by the original purchaser,  
freight prepaid, to:  
EURO-PRO OPERATING LLC, 94 MAIN MILL STREET, DOOR 16, PLATTSBURGH, NY 12901  
Proof of purchase date and $ 12.95 for handling and return packing/shipping charges must be included.  
The liability of EURO-PRO Operating LLC is limited solely to the cost of the replacement parts or the complete  
unit at our option. LABOUR CHARGES ARE NOT INCLUDED.  
This warranty does not cover normal wear of parts and apply to any unit that has been tampered with or used  
for commercial purposes. This limited warranty does not cover damage caused by misuse, negligent handling  
or damage due to faulty packaging or mishandling in transit (by any common courier).  
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional  
warranties. The responsibility of EURO-PRO Operating LLC, if any, is limited to the specific obligations  
expressly assumed by it under the terms of the limited warranty. In no event is EURO-PRO Operating LLC  
liable for incidental or consequential damages of any nature whatsoever. Some states do not permit the  
exclusion or limitation of incidental or consequential damages, so the above may not apply to you.  
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.  
PURCHASER  
DATE OF PURCHASE  
DEALER  
IMPORTANT: Carefully pack item to avoid damage  
-----------------------------------------------------------  
OWNERS REGISTRATION CARD  
Please complete and return within ten (10) days of purchase. The registration will enable us to contact you in the event a product  
defect is discovered. By returning this card, you acknowledge to have read and understood the instructions for use and warnings set  
forth in the accompanying instructions.  
RETURN TO: EURO-PRO Operating LLC, 94 MAIN MILL STREET, DOOR 16, PLATTSBURGH, NY 12901  
IN CANADA: EURO-PRO Operating LLC, 4400 BOIS FRANC, ST. LAURENT, QUEBEC H4S 1A7  
PURCHASER:  
ADDRESS:  
CITY:  
STATE:  
MODEL:  
DATE OF PURCHASE:  
NAME & ADDRESS OF DEALER:  
 

Edelbrock Automobile Parts R09399 User Manual
First Alert Smoke Alarm SA340 User Manual
Fisher Price Baby Swing B2108 User Manual
Ford Automobile FCS 15101 10 User Manual
Franklin Industries LLC Refrigerator FC 380 Series User Manual
Fujitsu Refrigerator 990TX2 User Manual
Gainward TV Receiver TV2GO User Manual
Garmin Marine GPS System 4010 User Manual
GE Clothes Dryer DBI333 User Manual
GE Conference Phone 25202 User Manual