Euro Pro Carpet Cleaner EP908H User Manual

STEAM CLEANER  
OWNER’S MANUAL  
Model EP908H  
120V., 60 Hz, 1550 Watts  
EURO-PRO Operating LLC  
94 Main Mill Street, Door 16  
Plattsburgh, NY 12901  
Tel.: 1 (800) 798-7398  
 
CARE & MAINTENANCE  
IMPORTANT SAFETY INSTRUCTIONS  
When using your Steam Cleaner basic safety precautions should always be  
If you consistently use demineralized or  
distilled water, cleaning the tank is  
unnecessary.  
observed, including the following:  
To reduce the risk of fire, electric shock, or  
injury:  
1. Read all instructions before using your  
steam cleaner.  
2. Use the system only for its intended use.  
3. To protect against a risk of electric shock,  
do not immerse any part of the system in  
water or other liquids.  
Rinsing out the steam cleaner:  
Do not leave the steam cleaner plugged  
in when unattended. Unplug the electrical  
cord when not in use and before servicing or  
refilling water tank.  
Normally, a periodic rinse of your steam  
cleaner will free it from deposits. This is  
recommended every 10-15 tankfulls, to  
free up any scale deposits from the tank.  
Fill the boiler with 20 oz. of water and  
shake the cleaner vigorously. Tilt the  
cleaner upside down to empty the boiler of  
water and any scale deposits.  
Do not allow to be used as a toy. Close  
attention is necessary when used by or near  
children, pets or plants.  
Use only as described in this manual. Use  
only manufacturer’s recommended  
accessories.  
Do not pull cord, use cord as a handle, close  
a door on cord, or pull cord around sharp  
edges or corners. Keep cord away from  
heated surfaces.  
Do not use extension cords or outlets with  
inadequate current carrying capacity.  
Do turn off all controls as applicable before  
unplugging from electrical outlet.  
Do not unplug by pulling on cord. To unplug,  
grasp the plug, not the cord.  
Do not handle plug or steam cleaner with wet  
hands or operate without shoes.  
Do not put any objects into openings. Do not  
use with any opening blocked.  
Do store your appliance indoors in a cool, dry  
area.  
4. Never yank cord to disconnect from  
outlet; instead, grasp plug and pull to  
disconnect.  
Fig. 10  
5. Do not allow cord to touch hot surfaces.  
Let the system cool completely before  
putting away or opening water tank  
(removing the safety cap). Wrap cord  
loosely around system when storing.  
6. Always disconnect system from electrical  
outlet when filling with water or emptying  
and when not in use. Always turn the  
safety cap slowly when opening the water  
tank . This will allow any remaining steam  
to escape gradually.  
7. Do not operate the system with a damaged  
cord or plug, or if the appliance or any other  
part of the system has been dropped or  
damaged. To avoid the risk of electric  
shock, do not disassemble or attempt to  
repair the steam cleaner. Return the  
system to EURO-PRO Operating LLC (see  
warranty) for examination and repair.  
Incorrect re-assembly or repair can cause a  
risk of electrical shock or injury to persons  
when the steam cleaner is used.  
8. Close supervision is necessary for any  
appliance being used by or near children.  
Do not leave the system unattended while  
connected to electrical outlet or when hot.  
9. Burns can occur from touching hot metal  
parts, hot water or steam. Use caution  
when draining unit after use as there may  
be hot water in the unit. Never direct steam  
at any person. The steam is very hot and  
can cause burns.  
10. Do not operate in the presence of  
explosive and/or flammable fumes.  
11. This appliance is intended only for  
household use. Follow all user instructions  
in this manual.  
Descaling your steam cleaner:  
If the tap water in you area contains a high  
level of calcium deposits and you have  
been using tap water to do your steam  
cleaning, you should descale your unit  
after 10-15 tankfulls.  
Step 1: Unplug the steam cleaner from  
the power source before you  
descale the boiler. Allow to cool.  
Step 2: Fill the boiler with 1 part  
vinegar and 5 parts water and  
leave overnight or for a period  
of approximately 8 hours. Do  
not screw the safety/filler cap  
onto the steam cleaner while  
you are descaling the boiler.  
Do not use the steam cleaner  
while descaling solution is  
inside the boiler.  
Fig. 11  
Do keep your work area well lit.  
Do Not turn the appliance over or on its  
side. Never direct steam towards people,  
animals or plants.  
Do not immerse the steam cleaner into water  
or other liquids. Always unplug the power  
cord from the electrical socket when filling the  
steam cleaner.  
Do NOT add cleaning solutions, scented  
perfumes, oils or any other chemicals to  
the water used in this appliance as this  
may damage the unit or make it unsafe for  
use. Use tap water or distilled/purified  
water if the tap water in your area is very hard.  
Step 3: After the period of soaking, turn  
the steam cleaner upside down  
to empty solution from the  
boiler. Due to the fact that a  
small amount of solution will be  
left in the boiler, it is necessary  
to rinse the boiler out with clean  
water 2 or 3 times. Your steam  
cleaner is now ready for use.  
Fig. 12  
Attaching the Shoulder Strap  
Using the detachable shoulder strap  
allows for greater freedom of movement  
when both hands are needed for various  
cleaning tasks.  
To attach the shoulder strap to the steam  
cleaner, simply snap the shoulder strap  
hooks onto the connecting rings on the  
unit body.  
Note: When storing your unit, always  
drain any residual water in the boiler  
and do not tighten the safety filler cap  
onto the unit. Always leave the safety  
filler cap loose on the unit when not in  
use.  
12. Never use any chemicals or substance  
other than tap water in the machine. Use of  
chemicals may damage the machine. Use  
of chemicals will automatically void your  
warranty.  
SAVE THESE INSTRUCTIONS  
See Fig. 10, 11 & 12.  
When using the Ultra Steam Shark II with  
the shoulder strap, avoid rocking or tilting  
the unit excessively as this may cause  
water to enter the hose and be  
For Household Use Only  
12  
discharged along with the steam.  
1
Rev. 09/04A  
 
USAGE SUGGESTIONS FOR STEAM CLEANER  
ADDITIONAL IMPORTANT SAFEGUARDS  
1. To avoid circuit overload, do not operate another appliance on the same socket  
(circuit) as the steam cleaner  
2. If an extension cord is absolutely necessary, an extension cord rated a minimum  
of 15 ampere, 14 gage cord should be used. Cords rated for less amperage may  
overheat. Care should be taken to arrange cord so that it cannot be pulled or  
tripped over.  
Exterior Areas  
Hints  
To clean inside your car, use the floor  
brush with a terry cloth towel attached to  
clean upholstery and interior areas just as  
in the home. You should not expose the  
bristles to leather - use only the brush with  
the terry cloth towel attached. For  
detailing the wheels, use the concentrator  
and the detail brush. Exterior windows  
are cleaned best by applying the vapor  
with the concentrator and following with a  
paper towel.  
ALWAYS FINISH CLEANING BY WIPING  
DOWN THE CLEANED SURFACE WITH  
A TOWEL  
The steam cleaner has many uses  
that have not been mentioned. This  
was meant only to give you a general  
idea of what can be achieved with the  
unit. However, the ways in which to  
use the attachments and brushes are  
in most cases universal. It is most  
helpful to always have a terry cloth  
towel or paper towel ready to use for  
removal of moisture and residue.  
100% white cotton towels work best.  
You can clean the brushes with your  
steam cleaner. To clean the floor  
brush, hold at one end and use the  
concentrator to simply blow off dirt  
into the garbage can. When cleaning  
the detail brush, use a pair of pliers to  
hold and blow dirt as above or place  
in the basket of your dishwasher.  
3. Do not leave unattended when the system is connected to a power  
supply/electrical outlet.  
SAVE THESE INSTRUCTIONS  
To clean bicycles, use the detail brush.  
FOR HOUSEHOLD USE ONLY  
To clean equipment, use the detail brush,  
depending on the surface area. Finish by  
wiping down with a towel.  
WARNING: This appliance is equipped with a grounded-  
type 3-wire cord (3-prong plug). This plug will only fit into an  
electrical outlet made for a 3-prong plug. This is a safety feature. If  
the plug should fail to fit the outlet, contact an electrician to replace  
the outlet. Do not attempt to defeat the safety purpose of the  
grounding pin, part of the 3-prong plug.  
Artificial Plants  
Use the concentrator without a brush  
attached to blow off the dust and dirt.  
Clothing  
A vapor cleaning system is excellent for  
removing wrinkles from fabrics. Simply  
“vaporize” the surface from a distance  
(12”-18”) The dry vapor removes wrinkles  
without leaving the fabric wet like ordinary  
fabric steamers do.  
Note: Wipe with a towel immediately  
before the cleaned area dries. When  
cleaning the oven, use the detail  
brush to clean around the elements  
and drip trays. Use the detail brush  
for cracks, crevices, and hard to reach  
areas.  
CAUTION: Always drain condensed water from hose  
before use or if unit has been left idle for a period of time. To  
drain hose, direct nozzle into an appropriate container or sink and  
depress hand grip steam trigger. Once hose has been drained,  
normal use may be resumed. Never direct nozzle  
Nicotine and Tar  
Nicotine and tar dissolves at high  
Refrigerator - Use the concentrator to  
blow away dirt in the ice machine and  
on door seals. The vapor will not dry  
out or crack the seals as chemicals  
often do. Can openers and other  
kitchen equipment can be easily  
cleaned with the detail brush to get  
into all the nooks and crannies. Mold  
stains around door gaskets can be  
removed with the detail brush.  
To clean microwaves or other small  
appliances use the detail brush for  
small areas.  
towards people, animals or plants.  
temperatures and becomes a light yellow  
oil that has the consistency of sewing  
machine oil. When the nicotine/tar film is  
touched by a hot terry cloth towel clipped  
over the floor brush, it immediately  
dissolves and flows into the towel. You  
can remove it from flat surfaces as fast as  
you can move the brush over the surface.  
Removing Wax, Tar, Etc.  
Many stains are only stuck on the surface  
of materials and can be easily and quickly  
removed by “blowing” excess material  
away from the surface from the side. This  
is accomplished by using the  
Note: When cleaning small electrical  
appliances always unplug them from  
outlet before cleaning.  
concentrator. Hold the terry cloth towel to  
the side to catch the loose residue as it is  
blown by the concentrator. Note: Always  
vacuum any loose residue off the surface  
before you apply vapor to it.  
To clean counter tops, use the floor  
brush with a terry cloth towel  
attached. For heavily soiled areas,  
use the brush without the terry cloth  
towel first in order to loosen the  
debris, then follow with a terry cloth  
towel attached to finish.  
2
11  
 
USAGE SUGGESTIONS FOR STEAM CLEANER  
GETTING TO KNOW YOUR STEAM CLEANER  
Window, Glass Surfaces and Mirrors  
Garden Furniture  
Use the dual edge glass and tile squeegee.  
Work with the vapor jet on using the top to  
bottom movements. Use the squeegee  
with the vapor off to clear the water from  
the glass. To do this without leaving  
streaks, use lateral movements from the  
top to the bottom of the surface.  
Use any of the brushes depending on the  
surface area. Work quickly when cleaning  
resin outdoor furniture. Finish by wiping  
with a towel  
Blinds  
Use the detail brush to clean blinds.  
Move the brush over the surface, allowing  
enough time for the vapor to penetrate.  
Work quickly on PVC blinds. Test for  
color fastness on fabric blinds before  
using. Finish by wiping with a towel.  
Fiberglass or Stainless Steel Surfaces  
Use the floor brush or detail brush. Slowly  
move the brush over the surface to be  
cleaned. The vapor will emulsify the dirt  
and grease on the surface. Follow behind  
with a terry cloth towel over the brush to  
remove excess moisture and residue.  
Bathroom Areas  
To clean the bathtub or shower area, use  
the detail brush for grout, shower door  
tracks, hard to get areas and heavily  
soiled areas. The dual edge window/tile  
squeegee will be the most efficient way to  
clean the rest of the area. Allow plenty of  
time for the heat to penetrate the surface.  
This is especially helpful in the shower  
area if there is tile or grout. Wipe with  
towel.  
Tip: An old idea for polishing stainless  
steel is to wipe it down with seltzer soda  
water after it is cleaned.  
Soap Scum  
Soap scum dissolves almost immediately  
under a combination of heat and moisture.  
Rinse the surface with a small amount of  
water afterwards or go back over it once  
more with a clean terry cloth towel.  
1. Power On Light (Red)  
2. Ready Light (Green)  
3. Handle  
4. Flexible Hose  
5. Hand Grip  
Removal of soap scum on tile, grout, and  
shower doors is also easier with the  
steam cleaner.  
6. Steam Trigger  
7. Safety Filler Cap  
8. Concentrator  
9. Floor Brush  
10. Extension Tubes (x2)  
11. Window Squeegee  
12. Detail Brush (x2)  
13. Shoulder Strap  
14. Funnel  
Note: Soap scum sometimes will develop a  
hard surface from waterborne minerals. If  
this is the case, use the floor brush with no  
towel first to break up this surface - or  
spray or wipe first with lemon, vinegar or  
seltzer soda water to soften the minerals.  
To clean sanitary fixtures, use the  
concentrator with or without detail brush.  
Use a terry cloth towel or paper towel to  
wipe up excess moisture and residue.  
To clean the sink and faucets, use detail  
brush then finish by wiping with a towel.  
Moving too slowly can dry out the soap  
scum and cause it to granulate on the  
surface. The surface will have a gritty feel.  
If this happens, apply vapor to the surface  
with the open brush again and re-clean.  
15. Power Cord  
16. Trigger Lock  
Technical Specifications  
Voltage:  
Power:  
120V., 60Hz.  
1550 Watts  
Water Capacity:  
Steam Generator:  
40 US Fl. Oz. (1200 ml.)  
Stainless Steel  
10  
3
 
FEATURES OF STEAM CLEANER  
USAGE SUGGESTIONS FOR STEAM CLEANER  
Wood, Vinyl and Marble Floors  
Spot Cleaning (Carpets)  
4. Heavy-duty crush-resistant  
1. No more detergents or  
chemicals. Just add water.  
4-ft hose.  
Use the concentrator with or without the  
detail brush. Move slowly over the soiled  
area, allowing the steam to penetrate.  
Agitate with detail brush or clean towel.  
Dab the spot with the towel (do not rub).  
Repeat as necessary to remove stain.  
Vacuum only after the carpet has  
completely dried.  
Always test color fastness of carpet in an  
inconspicuous area before cleaning.  
If your steam cleaner fails to remove  
stubborn stains a commercially available  
carpet shampoo may be required.  
Do NOT add cleaning solutions, scented  
perfumes, oils or any other chemicals to  
the water used in this appliance as this  
may damage the unit or make it unsafe  
for use.  
Use the floor brush with a terry cloth  
attached. Move the brush across the floor  
as if you are mopping. When the towel is  
soiled, allow to cool, then turn the towel  
over or replace it with a clean towel. If  
you are working on a very dirty area, you  
can move the brush over the area slowly,  
several times. If it is a wood floor, move  
fast to avoid heat or moisture buildup in  
the wood. By cleaning with the towel over  
the brush, you will not affect the shine on  
the floor.  
5. Versatile, quick-change  
accessories  
2. Lightweight & Portable  
To Strip Wax: Use floor brush for open  
areas; detail brush for corners or tight  
areas - no towel, slow strokes. Work a  
small area at a time - remove the  
emulsified wax from the floor. When all of  
the wax has been stripped, immediately  
clean the floor and brushes with water  
before residue has a chance to harden on  
them. Go back over the stripped area with  
the floor brush with a towel to remove any  
remaining residue before waxing.  
Upholstery  
Use the floor brush attached directly to  
the hand grip with a clean white terry  
cloth towel. Use fast, light strokes,  
avoid getting the fabric wet. Be patient  
with stubborn spots; work on a spot  
gently for no more than a minute at a  
time, then wait five minutes for the area  
to dry and repeat. Use circular  
movements or back-and-forth and side-  
to-side movements to get all sides of  
surface fibers then blot with a towel.  
Finish with a brushing in one direction  
that will give the fabric a uniform  
appearance.  
To Clean Waxed Floors: Wrap clean  
towel around the floor brush, brush  
quickly. This will cause the dirt to be  
removed but not the wax.  
6. Multipurpose Steam Cleaner:  
Bathrooms, kitchens, living  
areas, pet areas and  
appliances.  
3. Stainless Steel Boiler:  
Non-corroding, stainless  
steel boiler. Welded  
construction.  
Vinyl Floors: Do not allow heat to buildup  
in any kind of vinyl, since it can soften it  
enough to affect its texture. Work fast on  
vinyl.  
Automotive, patio and  
windows.  
Tile Floors: Use the concentrator with the  
detail brush attached to an extension.  
Have the floor brush with cloth attached  
ready as well. Clean the grout between  
the tiles with the detail brush. Remove the  
detail brush and attach the floor brush,  
move the brush across the floor to clean  
the tile and remove excess moisture and  
residue. For areas of tile that are very  
dirty, remove the towel and agitate with  
the brush. Do not let the area dry before  
you wipe with a towel.  
CAUTION: Always determine the  
color-fastness of any fabric-especially  
with reds or blues - by taking a clean,  
moist, warm towel and gently rubbing  
a small area as far down on the back  
or other out of the way place on the  
furniture as possible. If color comes  
off on the towel, you may need to  
have the piece dry cleaned.  
4
9
 
OPERATING INSTRUCTIONS  
OPERATING INSTRUCTIONS  
Components  
Tips On How To Use Your System  
Water  
Attaching the Accessories to the  
Flexible Steam Hose  
Step 4: Connect desired attachments  
onto the Flexible Steam Hose.  
Step 5: Plug the unit into a standard (120  
volt, grounded) wall receptacle.  
Allow approximately 8-10 minutes  
for vapor to reach its working  
Power “On” Light (red): This light will  
illuminate when the unit is plugged into  
the 120V. wall outlet and will remain on  
until the unit is unplugged.  
CAUTION: Read the instructions for  
“Filling the Water Tank” before opening  
the Safety Cap. Always depress hand  
grip steam trigger until all pressure/  
steam has been vented from boiler.  
CAUTION: Always unplug before  
filling. ALLOW UNIT TO COOL FOR  
FIFTEEN (15) MINUTES BEFORE  
REFILLING.  
IMPORTANT: Do NOT add cleaning  
solutions, scented perfumes, oils or any  
other chemicals to the water used in this  
appliance. Use tap water or  
Use tap water for all your cleaning  
needs.  
Dual Edge Glass & Tile Squeegee  
This attachment is very useful for  
cleaning large windows, plastic material,  
ceramic, tiled or marble surfaces.  
However, if you live in an area with  
hard water, use de-mineralized /  
distilled water when steaming light  
colored fabrics to eliminate the  
possibility of hard water stains.  
temperature and pressure. The  
green ready light will illuminate  
when the unit is ready for use.  
To use: Connect the tile  
squeegee to the hand  
grip or use with  
IMPORTANT: Do NOT add cleaning  
solutions, scented perfumes, oils or any  
other chemicals to the water used in  
this appliance. Use tap water or  
distilled/purified water if the tap  
water in your area is very hard.  
Step 6: Upon initial use, some water will  
come out from the nozzle of the  
attachment. This is unvaporized  
water in the hose and is normal.  
Always point nozzle in a safe  
direction.  
NOTE: When the steam cleaner has  
run out of water, steam output will  
cease.  
extension tube for  
hard to reach surfaces.  
Apply steam abundantly, rub with the  
soft spongy edge, then remove excess  
water and dirt with the glass wiping  
edge.  
WARNING: A towel wrapped around  
the brush can become hot enough to  
burn. Make sure that you let the towel  
cool off for 5 minutes before touching it.  
IMPORTANT:When cleaning  
windows, always avoid any sudden  
changes in temperature to prevent glass  
breakage or cracks.  
distilled/purified water if the tap water  
in your area is very hard.  
WARNING:Always drain the  
Filling Your Steam Cleaner With  
Water  
Using Towels  
condensed water from hose before  
use or if unit has been left idle for a  
period of time. To drain hose, direct  
nozzle into an appropriate container or  
sink and depress hand grip steam  
trigger. Once hose has been drained,  
normal use may be resumed. Never  
direct nozzle towards people, animals  
or plants.  
Concentrator  
For best results use 100% cotton  
white terry cloth towels.  
Attach the concentrator  
to the handgrip or to the  
extension tubes. Then  
attach the detail brushes  
to the concentrator.  
IMPORTANT: Always insure that the unit  
is “UNPLUGGED” from the wall receptacle  
prior to initial filling or re-filling the water  
tank. Never attempt to fill this unit under  
a water tap, always use the filling funnel  
provided. Failure to follow these steps will  
cause the water tank to overfill and may  
pose an electrical safety hazard.  
Use correct size of towel to allow you  
to wrap the towel around the brushes  
and clip it under the spring loaded  
cloth holder.  
The purpose of using a towel is to  
absorb moisture and dirt being  
removed. Always use dry towels.  
A wet towel will smear the dirt.  
Wash towels with strong detergent  
and bleach.  
Using scented fabric softener while  
washing the towels will cause the  
scent to be released into the air  
when using the towels with your  
steam system.  
Detail Brush  
It is best for cleaning grout in-between  
the tiles, ceramic and marble.  
To use: Attach the detail  
brush on to the end of the  
concentrator, which  
then may be used directly  
on the hand grip or with the extension  
tubes.  
Step 1: Before filling the steam cleaner,  
make sure that the unit is NOT  
plugged in and has been allowed to  
cool for fifteen (15) minutes.  
Step 2: Squeeze and hold handgrip trigger  
until all pressure has been released  
from the boiler. Turn Safety/Filler  
Cap counter clockwise until  
removed. (See caution above.)  
Step 3: Place the appliance on a flat,  
stable surface and insert the funnel  
into the tank opening and add 40  
US fl. oz. (1200 ml) of water.  
Vent Hole  
Efficient Work  
For vertical surfaces, wipe with a  
towel from the top down, in this  
way the dirty water will not soil  
surfaces already cleaned.  
Fig. 1  
(Fig. 1) Place the funnel in the tank  
opening as illustrated in Fig. 1. The  
funnel has been specially designed  
to show when the water tank is full.  
When water starts to come out of  
the vent hole of the funnel, the tank  
is full. Remove the funnel slowly  
and let the remaining water in it to  
go inside the water tank. Do Not  
Overfill. Replace the Safety Filler  
Cap.  
WARNING:Allow unit to cool for 15  
minutes before refilling. When  
refilling the steam cleaner while it is still  
hot, the first drops of water might bubble  
up. Use caution when opening the  
Safety/Filler Cap as cap may become  
hot during use and escaping steam  
can cause scalding.  
Avoid changing brushes back and  
forth while cleaning.  
Start with the smallest brush to  
clean tight spots and corners first.  
Use a towel to wipe dirt as soon as  
possible, otherwise it will dry and  
re-adhere to the surface.  
8
5
 
OPERATING INSTRUCTIONS  
OPERATING INSTRUCTIONS  
Attaching a Towel to the Floor  
Brush  
Refilling Your Steam Cleaner  
With Water  
Step 1: Disconnect electrical power cord  
from wall outlet.  
Step 2: Depress and hold the hand grip  
steam trigger to ensure that any  
remaining pressure in the boiler  
has been released.  
Step 3: Carefully loosen the safety/filler  
cap by turning counter clockwise.  
Any residual steam will be  
100% white terry cloth towel can be fitted  
on this brush, so as to absorb the dirt and  
protect delicate surfaces.  
Fig. 2  
Important: Please note that bristles may  
break through thin towels. To cut and make  
your own towels, we recommend that you  
use one (1) towel 8” x 17” folded in half or  
two (2) towels 4” x 17” laid one on top of  
the other be used. This will ensure that the  
brush bristles do not break through and  
that the towels will be sufficiently absorbent  
and retain as much dirt as possible.  
Very Important: When installing the  
towels to the floor brush, ensure that the  
towels do not cover the front and the back  
of the brush. (See Fig. 9)  
Fig. 7  
4. Fold the other side of the towel as  
shown in Fig. 7.  
released below the safety/filler  
cap if the tank has not been  
completely vented. When the  
hissing stops and the last of the  
steam has been released,  
remove the filler cap. Allow unit  
to cool down.  
Fig. 3  
NOTE: Fit floor brush with the angle  
adapter on to the extension  
tube.  
CAUTION: Allow unit to cool for 15  
minutes before refilling. If the steam  
cleaner is still hot, there is a risk that  
water will squirt back during filling and  
cause scalding. Extreme care should  
be taken when refilling the unit. Use  
caution when opening the safety/filler  
cap as cap may become hot during use  
and escaping steam can cause  
scalding.  
Step 2: If the angle adapter is not  
attached to the floor brush,  
hold the brush with its bristles  
up in your left hand. With the  
angle adapter pointing  
downward, insert it into the  
hole in the back of the brush,  
then turn the floor brush 180°.  
Step 3: Insert the electrical power cord  
into the wall outlet. Heating  
time is approximately 8-10  
minutes with cold water. Filling  
the steam generator with hot  
water will shorten the heat up  
time.  
Fig. 8  
5. Place the corner under the cloth  
holder as shown in Fig. 8.  
Step 4: Allow the steam cleaner to cool  
for 15 minutes before re-filling  
with water.  
Step 5: Refill water tank with water using  
the filling funnel.  
Step 6: Firmly screw the safety/filler cap  
back onto the unit by turning  
clockwise.  
Step 7: Connect power cord to the wall  
outlet.  
Fig. 5  
1. Prepare white terry cloth towel:  
size 8” x 17” folded in half or place one  
on top of another to have two layers.  
(Fig. 5)  
Note: If you require continuous steam,  
depress the trigger and engage the  
trigger lock. (Fig. 2)  
Fig. 9  
2. Place the brush on top of the towel.  
Cleaning the Floor Brush  
6. Place the towel around the brush,  
and repeat folding the towel as shown  
in Fig. 9. When folding the towel,  
leave some slack. Do not pull tightly  
around the brush, leave some  
looseness.  
To clean the floor brush after you have  
finished using:  
Using Your Steam Cleaner with  
Floor Brush  
Step 1: Connect one of the extension  
tubes to the hand grip on the  
flexible steam hose. To  
1. Lift the front clip on the floor  
brush (Fig. 4) and remove the brush.  
2. Rinse the bristle brush and the  
diffuser housing under warm water.  
3. Replace bristle brush onto the diffuser  
housing.  
attach the extension tubes  
one onto the other or  
onto the hand grip, press the  
locking button ensuring that it  
fits into the hole. (Fig. 2, Fig. 3)  
To disconnect, repeat the  
operation by pressing the locking  
button and pulling the two  
sections apart.  
Fig. 6  
3. Fold the towel as shown in Fig. 6.  
Fig. 4  
6
7
 

Echo Brush Cutter SRM 340 User Manual
Electro Voice Speaker Force i Sub User Manual
Excalibur electronic Home Safety Product H631 User Manual
Extron electronic Cable Box 60 161 01 User Manual
Extron electronic Universal Remote 68 1323 01 User Manual
Fisher Price Automobile Parts C2474 User Manual
Foundry Networks Network Hardware FGS624P User Manual
Fujitsu Power Supply MB3878 User Manual
Garmin GPS Receiver 1100 User Manual
GBC Laminator 930 400 User Manual