Euro Pro Iron EP480 User Manual

1600 Watt Professional  
Steam Iron  
FOR THE WAY YOU LIVE  
Model EP480  
USE AND CARE INSTRUCTIONS  
Congratulations!  
You are the owner of the EURO-PRO 1600 Watt Professional Steam Iron. To  
fully enjoy the advantages of your appliance, please take a few minutes to read  
all the “Use & Care Instructions” and keep the instructions handy for easy  
reference. Please review the product warranty and mail the owner registration  
form.  
U.S.:  
EURO-PRO Operating LLC  
94 Main Mill Street, Door 16  
Plattsburgh, NY 12901  
CANADA:  
EURO-PRO Operating LLC  
4400 Bois Franc  
St. Laurent, QC H4S 1A7  
Tel.: 1 (800) 798-7398  
 
SPECIAL INSTRUCTIONS  
1. To avoid a circuit overload, do not operate another high-wattage appliance on the same circuit.  
2. If an extension is absolutely necessary, a 15-ampere rated cord with a polarized plug should be used.  
Cords rated for less amperage may overheat.  
Care should be taken to arrange the cord so that it cannot be pulled on or tripped over.  
POLARIZED PLUG: This appliance has a polarized plug (one blade is wider than the other).  
As a safety feature, this plug will fit into a polarized outlet only one way. If  
the plug does not fit fully into the outlet, reverse the plug.  
If it still does  
not fit, contact a qualified electrician.  
feature.  
Do no attempt to defeat this safety  
SAVE THESE INSTRUCTIONS  
3
 
EURO-PRO PROFESSIONAL STEAM IRON  
1. Power Supply Cord  
2. Auto Shut-Off Light  
3. Thermostat Light  
4. Variable Steam Control  
5. Burst of Steam Button  
6. Spray Button  
8. Spray Nozzle  
9. Temperature Control Dial  
10. Water Level Window  
11. Stainless Steel Soleplate  
12. Water Measuring Beaker  
13. Iron Heel Rest  
7. Water Filling Inlet Cover  
4
 
IMPORTANT  
Resetting After Auto Shut-Off  
The auto shut-off safety function of your EURO-PRO EP480 Iron is designed to engage after  
approximately 8 minutes of non use. The blue indicator light will flash when the auto shut-off has  
activated.  
To reset your iron and continue ironing follow these steps.  
1) Lift iron from stand.  
2) Holding the iron horizontally in front of you, gently rock the iron back and forth several times.  
This motion will reset the safety switch inside the iron. Do not shake the iron.  
The red temperature light will illuminate when the auto shut-off system has been reset.  
Allow time for the iron to re-heat.  
The red indicator light will go out when the iron is ready for use.  
Caution: Do not use the auto shut-off feature as a substitute for turning the  
iron off and unplugging the iron when not in use.  
5
 
BEFORE FIRST USE  
Remove any labels, stickers or tags which may be attached to the body or  
soleplate of the iron before using the iron.  
Read all instructions for use carefully.  
Always follow the Important Safeguards.  
IMPORTANT  
The first time an iron is used, some odor and small white particles may come out of the steam vents.  
This is perfectly normal and will cease to occur after the iron has been in use for a short while.  
Before you start using your iron, follow the instructions in the manual and do the following  
in order to eliminate any odor and small white residue particles and to ensure optimum steam  
performance.  
• Fill the iron with regular tap water.  
• Set the temperature control dial at its highest and steam control at ‘0’.  
• When the thermostat light goes off to indicate that the iron has reached the selected  
temperature, set the steam control at MAX.  
• Keep the iron in a horizontal position and allow it to steam until the water runs out.  
• Press the steam burst button to eliminate white residue particles.  
• Repeat this procedure through 2 or 3 fillings of water.  
6
 
CHOOSING THE IRONING TEMPERATURE  
Set the temperature dial according to the type of fabric .  
• Synthetics  
(low temperature)  
• • Silk, Wool  
(medium temperature)  
• • • Cotton, Linen  
(high temperature)  
Temperature Control Dial  
Variable Steam Control  
Please note: Before starting to iron delicate fabrics, it is best to first test the  
temperature of the iron on a hem or an inside seam.  
CONNECTING THE IRON TO THE POWER SUPPLY  
• Make sure that the variable steam control dial is set at ‘0’.  
• Place the iron upright on the heel rest.  
• Select the required temperature setting on the temperature control dial.  
• The red thermostat light will come on indicating that the iron is heating up.  
• When the red light goes out, the set temperature has been reached and the iron is  
ready to use.  
• The thermostat ready light will go on & off as the thermostat is switching the heating  
element on & off to maintain the selected temperature.  
7
 
FILLING WITH WATER  
• Ensure the unit is unplugged from the main supply before  
filling.  
• Set the variable steam control (4) to position "MIN"  
(ie. No steam)  
• slide the water filling inlet cover (7) down and use the  
measuring beaker (12) to pour the water in through the  
filling aperture (see picture).  
• Do not overfill.  
Note: Regular tap water can be used up to 12 grains water hardness but if your  
water exceeds this we suggest using 1/3 tap water and 2/3 distilled water.  
Never use 100% distilled water as this could cause water spitting and low  
steam performance.  
8
 
IRONING WITH STEAM  
• Make sure iron is unplugged from power source.  
• Set the variable steam control to ‘0’.  
• Fill the iron with water following the instructions for filling.  
• Plug the cord into a 120 Volt AC electrical outlet.  
• Set the temperature control dial within the steam area i.e. ‘•••’.  
• Make sure that the iron has reached the selected temperature with the variable  
steam control set at ‘0’.  
IMPORTANT:  
Do not open the steam control until the thermostat light goes off to  
indicate that the selected temperature within the steam range has  
been reached. If you move the variable steam control up from ‘0’  
before the correct temperature is reached, the iron will drip water.  
• The variable steam control offers a few different settings:  
PLEASE NOTE: For maximum steam the temperature control dial should be  
set at ••• .  
The temperature control should be set at the beginning only for very  
delicate fabrics requiring very gentle steam (setting •).  
• Steam is produced as soon as the iron is held in a horizontal  
position.  
• Steam will stop coming out when the iron is put on its heel in  
a vertical position or by turning the steam control dial to ‘0’.  
• Vertical steam: For vertical burst of steam, pump control  
button (5) located on the top of the handle selection of your  
iron. The vertical steam function is useful for steaming curtains  
and drapes will still hanging, or for powering out stubborn  
wrinkles while ironing on a board.  
9
 
WATER SPRAY  
• Use the spray button to add moisture to stubborn wrinkles.  
• First make sure that there is water in the tank.  
• Press the spray button (6) slowly to get a jet spray.  
• Press the spray button strongly and quickly to get a mist.  
• Please note: If spray does not come out when you press the  
spray button, cover the spray opening with your finger and press  
a few times.  
TO EMPTY THE IRON  
• Always empty iron after each usage.  
• After using the iron, turn the variable steam control to ‘0’  
and the temperature control dial to ‘minimum’.  
• Unplug the iron from the power source.  
• Set variable steam control to ‘MAX’.  
• Open the water inlet cover and turn the iron up-side down  
over the sink with the tip pointing downward and allow the  
water to flow from the opening.  
• Set variable steam control to ‘0’.  
• Allow iron to cool on the iron rest before storing.  
WARNING: Use caution when you turn the iron up-side down- there may be hot  
water in the reservoir. Burns can occur from touching hot metal  
parts, hot water or steam.  
10  
 
TO ADD WATER  
• Unplug iron from the electrical outlet.  
• Follow instructions to empty the iron.  
• Then, follow the instructions for filling the iron.  
Following this procedure will ensure that you do not overfill the iron.  
SELF-CLEANING  
In order to remove calcium and built-up particles, the self-cleaning system should be run at least  
once a month.  
• Fill the watering beaker provided to the half-full mark and then pour into the water reservoir.  
• Set the variable steam control (4) to the no steam position.  
• Insert the main plug into the wall socket.  
• Set the temperature control dial (9) to the maximum temperature.  
• Wait until the thermostat light (3) goes off and steam iron has reached preset temperature.  
• Remove the plug from the wall socket.  
• Hold the steam iron horizontally over a sink.  
• Turn the variable steam control (4) to “Self-Clean  
” position. Hot water and steam will  
be emitted from the soleplate. Swing the steam iron lightly back and forth gently to allow lime  
and dust particles to come out.  
• When the water reservoir is empty, shift the variable steam control from “Self-Clean” position  
to “0”.  
• Stand the iron upright and insert the plug into the wall socket to let the iron heat up again.  
• Move the iron over a clean cotton cloth to clean the soleplate and let the remaining water on  
the soleplate evaporate.  
11  
 
CLEANING, STORAGE & MAINTENANCE  
• Always turn the variable steam control to ‘0’ after you have emptied the water tank.  
• Allow iron to cool down.  
• Always store the iron on the metal iron rest or in an upright position on it’s heel rest  
to protect the soleplate.  
• From time to time clean the exterior with a damp cloth and wipe dry.  
• If you use spray starch, wipe the soleplate occasionally with a soft damp cloth to  
prevent the forming of a deposit.  
• If the iron has not been used for a few weeks, hold the iron horizontally and allow it to  
steam for 2 minutes before ironing.  
WARNING: The anti-drip function reduces water dripping and water stains. It  
does not prevent water dripping or water stains if you press the  
steam burst button too often or if temperature is too low. The  
amount of water droplets will eventually decrease after iron is  
used for 2 to 3 tankfuls of steaming and ironing.  
12  
 
Iron Troubleshooting  
Problems  
Potential Reasons & Solutions  
Iron should be plugged into a 120V AC electrical outlet  
only. Make sure that the plug is securely in the socket.  
• Thermostat set too low. Turn to higher setting.  
• Auto shut-off may be activated. Move iron gently or  
shake.  
Iron does not heat  
This is normal. The light goes On and Off as the  
thermostat is switching the heating element On and Off  
to maintain the selected temperature.  
Thermostat ready light goes On and Off  
This is normal. Follow instructions for first use and allow  
iron to steam through 2-3 fillings & press the steam burst  
button occasionally to eliminate small white particles.  
Some odor or small particles come out of  
steam vents of new iron  
• Water tank may be empty or water level is very low.  
Add water.  
Iron does not steam  
• Make sure that the temperature control dial and the  
variable steam control are correctly set. For maximum  
steam (setting ‘Max’ on steam control), temperature  
control dial should be set on ‘•••’.  
• Always allow the iron to reach the selected temperature  
with the steam setting at ‘0’. Make sure the temperature  
control dial is set in the correct steam area and the steam  
control is not on ‘0’. For more steam, turn temperature  
dial to higher setting (e.g. ‘•••’ and the steam control to  
‘Max’).  
• If temperature setting and steam control setting are  
correct and there is no steam, gently tap the soleplate on  
the ironing board a few times. Move the variable steam  
control from ‘0’ to ‘Max’ a few times.  
13  
 
Iron Troubleshooting (continued)  
Problem  
Water droplets coming from steam vents  
Potential Reasons & Solutions  
• Iron may not be hot enough. Set thermostat to the ‘max’  
position. Always allow iron sufficient time to heat up  
(thermostat light goes off) before activating the variable  
steam control.  
• Auto-Off may be activated. Move iron or gently shake.  
• Overuse of steam burst. Allow more time between each  
burst.  
• Iron may have been overfilled. Turn iron off, empty water  
and follow instructions for filling.  
• Steam performance may be low if iron requires  
seasoning. Use regular tap water for 1or 2 tanks until  
steam performance improves.  
14  
 
IMPORTANT SERVICE INFORMATION  
In the event that  
your iron fails to operate properly  
or  
if your iron needs servicing  
DO NOT RETURN IT TO THE STORE  
First check the troubleshooting guide on the back of this page and make sure that you have  
followed all the instructions in the operating manual. If your iron still does not operate  
properly, send your iron, together with $9.50 to cover the cost of return shipping and handling,  
and a copy of your sales receipt to:  
U.S.:  
CANADA:  
EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901  
EURO-PRO Operating LLC, 4400 Bois Francs, St. Laurent, QC, H4S 1A7  
If the warranty period has expired, please send your iron postage pre-paid to the Service Dept. of EURO-  
PRO Operating LLC at the above address. You will be advised of the cost of repair before any servicing is  
done unless you enclose a note indicating that you would like us to proceed with the repairs and return the  
iron to you C.O.D.  
DO NOT FORGET TO ENCLOSE  
YOUR NAME, ADDRESS, TELEPHONE NUMBER AND COPY OF SALES RECEIPT.  
 
ONE YEAR LIMITED WARRANTY  
EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one (1) year from the  
date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions. If your  
appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance  
and accessories, freight prepaid to:  
U.S.:  
CANADA:  
EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901  
EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7  
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of charge.  
Proof of purchase date and $ 9.95 to cover the cost of return shipping and handling must be included. *  
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty  
does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This  
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in  
transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or  
alterations to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.  
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility  
of EURO-PRO Operating LLC if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In  
no event is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever. Some states do not  
permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you. This warranty gives you  
specific legal rights, and you may also have other rights which vary from province to province.  
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item  
before packing with your name, complete address and phone number with a note giving purchase information, model number and  
what you believe is the problem with item. We recommend you insure the package (as damage in shipping is not covered by your  
warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our  
products, therefore the specifications contained herein are subject to change without notice.  
PRODUCT REGISTRATION CARD  
FOR CANADIAN CONSUMERS ONLY  
Please complete and return within ten (10) days of purchase. The registration will enable us to contact you in the event a product defect is discovered.  
By returning this card you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.  
Please return to:  
IN CANADA:  
EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, QC, H4S 1A7  
PURCHASER: _________________________________________________________________________________________  
ADDRESS: ____________________________________________________________________________________________  
EP480  
DATE OF PURCHASE: __________________ MODEL: ______________ SERIAL NO: ______________________________  
NAME AND ADDRESS OF STORE: ________________________________________________________________________  
 

Compaq Personal Computer PC 5510 User Manual
Cooper Lighting Home Safety Product AP2SQ User Manual
Craftsman Lawn Mower 917259561 User Manual
Crate Amplifiers Stereo Amplifier DX 112 User Manual
Creda Cooktop CB01E User Manual
Dyson Vacuum Cleaner DC31 User Manual
Electro Voice Portable Speaker DMC 1152X User Manual
Electro Voice Portable Speaker MTH 25 22BT User Manual
Festool Saw PD561593 User Manual
Garland Convection Oven MCO GD 10E User Manual