Euro Pro Iron EP171 User Manual

Shark Compact Performer  
Model EP171  
Use and Care Instructions  
Congratulations!  
You are the owner of the Shark Compact  
Performer Iron. To fully enjoy the advantages of your appliance,  
please take a few minutes to read all the “Use & Care Instructions”  
and keep the instructions handy for easy reference. Please review  
the product warranty and mail the owner registration form.  
For information or assistance:  
USA: EURO-PRO Operating LLC  
21 Lawrence Paquette Industrial Drive  
Champlain, NY 12919  
Tel.: 1-866-98SHARK  
 
IMPORTANT SAFEGUARDS  
When using your iron, basic safety precautions should always be followed,  
including the following:  
1. Read all instructions before using the iron.  
2. Use iron only for its intended use.  
3. To protect against a risk of electrical shock, do not immerse in water or  
other liquids.  
4. The iron should always be turned “OFF” before plugging or unplugging  
from electrical outlet.  
5. Never yank cord to disconnect from outlet, instead grasp plug and pull to  
disconnect.  
6. Do not allow cord to touch hot surfaces. Let iron cool completely before  
storing.  
7. Loop cord loosely around iron when storing.  
8. Always disconnect iron from electrical outlet when filling iron with water or  
emptying and when not in use.  
9. Do not operate iron with a damaged cord or if the iron has been dropped  
or damaged.  
10. To avoid the risk of electrical shock, do not disassemble the iron. Return  
appliance to EURO-PRO Operating LLC for examination, repair or  
adjustment. Incorrect reassembly can cause a risk of electric shock when  
iron is used.  
11. Close supervision is necessary for any appliance used by or near children.  
Do not leave iron unattended while connected or on an ironing board.  
12. Burns can occur from touching hot metal parts, hot water or steam. Use  
caution when you turn a steam iron upside down as there may be hot  
water in the reservoir.  
13. Never direct steam at any person, especially when using the iron in a  
vertical position. The steam is very hot and can cause burns.  
14. Do not use iron outdoors.  
15. This product is for household use only.  
SPECIAL INSTRUCTIONS  
1.To avoid a circuit overload, do not operate another high-wattage appliance on  
the same circuit.  
2.If an extension is absolutely necessary, a 10-ampere rated cord with a  
polarized plug should be used. Cords rated for less amperage may overheat.  
Care should be taken to arrange the cord so that it cannot be pulled on or  
tripped over.  
IMPORTANT: This appliance has a polarized plug (one blade is wider than  
the other). As a safety feature, this plug will fit into a polarized outlet only  
one way. If the plug does not fit fully into the outlet, reverse the plug. If it  
still does not fit, contact a qualified electrician. Do no attempt to defeat this  
safety feature.  
FOR HOUSEHOLD USE ONLY  
SAVE THESE INSTRUCTIONS  
Rev. 04/02B  
 
TROUBLESHOOTING  
PROBLEM  
POSSIBLE REASONS & SOLUTIONS  
Shark Compact Performer  
Model EP171  
• Make sure that the plug is securely in the socket.  
• Temperature setting too low.  
Turn to higher setting.  
Iron does not heat  
115/230 V., 60Hz., 800 W.  
• This is normal.  
Thermostat ready light  
goes On and Off  
The light goes On and Off as the thermostat is  
switching the heating element On and Off to  
maintain the selected temperature.  
Main Components  
Some odor or small  
particles come out of  
steam vents of new  
iron  
• This is normal.  
Follow instructions for first use and allow iron to steam  
through 2-3 fillings & press the steam burst button  
occasionally to eliminate small white particles.  
Iron does not steam  
• Water tank may be empty or water level is very low.  
Add water.  
• Make sure that the temperature control dial and  
the steam control are correctly set. For  
maximum steam, (setting ‘Max’ on steam control),  
temperature control dial should be set on ‘•••’.  
• Adjustable steam control is set on “0”.  
Always allow the iron to reach the selected  
temperature with the adjustable steam control setting  
at ‘0’. Make sure the temperature control dial is set in  
the correct steam area, e.g. ‘•’, and the steam control is  
not on ‘0’. For more steam, turn temperature dial to  
higher setting, e.g. ‘•••’, and the steam control to ‘Max’.  
• If temperature setting and steam control setting are  
correct and there is no steam, gently tap the  
soleplate on the ironing board a few times. Move  
the steam control from ‘0’ to ‘Max’ a few times.  
1. Water Filling Inlet  
2. Steam Control Dial  
3. Spray/Burst of Steam Selector Button  
4. Temperature Control Dial  
5. Thermostat Light  
6. Dual Voltage Switch  
7. Spray Nozzle  
• Iron may not be hot enough. Set thermostat to the  
‘Max’ position. Always allow iron sufficient time to  
heat up (thermostat light goes off).  
• Overuse of steam burst. Allow more time between  
each burst.  
• Iron may have been overfilled. Turn iron off,empty  
water and follow instructions for filling.  
• Steam performance may be low if iron requires  
seasoning. To season, use regular tap water for 1or 2  
tanks until steam performance improves.  
Water droplets coming  
from steam vents  
8. Stainless Steel Soleplate  
9. Water Measuring Beaker  
1
10  
 
IRONING CHART  
BEFORE FIRST USE  
NOTE: Before starting to iron delicate  
To select iron temperature, align  
temperature selected on dial with  
the indicator on the water tank.  
Remove any labels, stickers or tags which may be attached to the body or  
soleplate of the iron before using the iron.  
Read all instructions for use carefully. Always follow the Important Safeguards.  
fabrics, it is best to first test the  
temperature of the iron on a hem or an  
inside seam.  
IMPORTANT  
The first time an iron is used, some odor and small white particles may come  
out of the steam vents. This is perfectly normal and will cease to occur after the  
iron has been in use for a short while.  
DIRECTIONS  
ON LABEL  
Before you start using your iron, follow the instructions in the manual and do the  
following in order to eliminate any odor and small white residue particles and to  
ensure optimum steam performance.  
SYNTHETIC  
• Fill the iron with regular tap water.  
FIBERS, e.g.  
acrylic, nylon  
polyester  
SILK  
COTTON  
LINEN  
• Set the temperature control dial to its highest setting, the spray/burst of steam  
button to the steam setting and the steam control knob to the lowest steam  
setting.  
FABRIC  
WOOL  
• When the thermostat light goes off to indicate that the iron has reached the  
selected temperature, set the steam control knob to the highest setting.  
• Keep the iron in a horizontal position and allow it to steam until the water runs  
out.  
• Press the spray/burst of steam button to eliminate white residue particles.  
• Repeat this procedure through 2 or 3 fillings.  
TEMP.  
CONTROL  
MIN  
MAX  
• • • • •  
OPERATING INSTRUCTIONS  
Before using your iron, check the voltage and type of plug that is required for  
your location. If necessary, readjust the dual voltage switch according to local  
voltage: 110V - 120V or 220V - 240V. This is accomplished by sliding the dual  
voltage control switch located in the rear of the iron to the corresponding  
voltage setting.  
BURST OF  
STEAM  
SPRAY  
Caution: Always disconnect the iron before adjusting the dual voltage  
switch to the correct voltage setting.  
9
2
 
OPERATING INSTRUCTIONS cont.  
Filling with Water  
USER MAINTENANCE INSTRUCTIONS  
EMPTYING, CLEANING & STORING THE IRON  
WARNING! Before filling the iron with water, be sure the iron is not  
plugged into the electrical outlet. The iron may be filled with  
water while it is hot.  
Always empty and clean your iron after each use and before storing.  
1. Turn the temperature control dial to the “Off” position  
2. Unplug the power cord from the electrical outlet.  
3. Empty the iron of all remaining water in the water reservoir.  
4. Allow the iron to cool down before cleaning.  
5. When the iron has cooled down completely, scale and other residue  
can be wiped off the soleplate with a damp cloth.  
6. Store iron in the upright position.  
TO PREVENT THE RISK OF BURNS, use caution when filling  
iron with water. Burns can occur from touching hot metal  
parts, hot water or steam.  
CAUTION:Never fill the iron with fabric conditioner, starches or any  
other liquid, as these will damage the steam mechanism. Do  
not use contaminated water.  
WARNING! Use caution when emptying the iron. Burns may occur  
from touching hot metal surfaces, hot water or steam.  
NOTE: Because of the soleplate design, ordinary tap water may be used with  
this iron. However, in very hard water areas, we recommend using  
distilled or demineralized water.  
1. Disconnect the iron from the power supply.  
2. Open the water inlet cover.  
3. Using the measuring beaker provided and holding the iron at a slight  
angle, pour water slowly into the water filling inlet. See illustration below.  
DO NOT overfill the tank.  
4. Plug the cord into a polarized, 120V AC electrical outlet.  
5. Turn the temperature control dial to the desired temperature setting and  
allow the iron to heat for approximately 2 minutes before ironing. Place  
iron on its heel (on a stable, protected surface) while the iron is warming  
to desired temperature. The thermostat light will come on. When the iron  
has reached the desired temperature , the thermostat light will go “Off”.  
3
8
 
OPERATING INSTRUCTIONS cont.  
OPERATING INSTRUCTIONS cont.  
SETTING THE IRON TEMPERATURE  
DRY IRONING  
All marked settings on the temperature dial can be used for dry ironing.  
1. Plug the cord into a polarized, 120V AC electrical outlet. The thermostat light  
light will go “On”, indicating that the iron is receiving power.  
2. Set Steam Control Knob to no steam setting.  
3. Set Temperature Control Dial to desired temperature setting.  
4. Place iron on its heel (on a stable, protected surface) while iron is  
warming to desired temperature.  
Set the temperature dial according to the type of fabric.  
Synthetics  
(low temperature)  
• • Silk, Wool  
(medium temperature)  
• • • Cotton, Linen  
(high temperature)  
5. When the iron has reached the desired temperature, the thermostat  
light will go “Off”.  
Please note: Before starting to iron delicate fabrics, it is best to first test  
the temperature of the iron on a hem or an inside seam.  
1. Set the temperature control dial to the desired temperature.  
2. Stand the iron on its heel and connect it to the main power supply.  
3. The thermostat light will come on to indicate that the iron is heating  
up. The light will go “Off” when the set temperature has been  
reached and the iron is ready to use. The thermostat light will go on  
and off as the thermostat is switching the heating element on and off  
to maintain the selected temperature.  
SPRAY SETTING  
The water spray is useful on fabrics with stubborn wrinkles. Press the spray  
button and a jet of water will spray onto the fabric being ironed. The water  
spray can be used with dry or steam ironing as desired.  
1. Disconnect the iron from the power supply.  
2. Follow filling instructions on page 3.  
3. Plug the power cord into the electrical outlet.  
4. Set Temperature Control Dial to desired temperature setting.  
5. Set Spray/Burst of Steam Button to spray position.  
6. Press the Spray/Burst of Steam button slowly to get a jet of spray.  
7
4
 
OPERATING INSTRUCTIONS cont.  
IRONING WITH STEAM  
OPERATING INSTRUCTIONS cont.  
BURST OF STEAM & VERTICAL STEAM  
Please note: Before using the iron for the first time, it is important to  
purge the inside of the iron by allowing it to steam freely for  
a minute. This allows the removal of any impurities left by  
the manufacturing process.  
WARNING! DO NOT aim iron at face, towards yourself, or anyone else while  
using or adjusting steam. Burns or serious injury may occur.  
The burst-of-steam button is useful when ironing denim, cotton and linens. It  
provides extra, sudden blasts of steam which aid in removing stubborn  
wrinkles.  
WARNING!DO NOT aim iron at face, towards yourself, or anyone else while  
using or adjusting steam. Burns or serious injury may occur.  
The burst-of-steam & vertical steam feature can be used with Dry or Steam  
ironing as desired.  
1. Make sure the water tank is filled with water.  
2. Follow filling instructions on page 3.  
3. Plug the power cord into the electrical outlet.  
4. Set the temperature control dial within the steam area, i.e. “• • • ”.  
(See page 4 for setting the temperature.)  
5. The thermostat light will go “On”.  
6. When the correct temperature has been reached, the thermostat  
light will go “Off”.  
7. Now turn the Spray/Burst of Steam button to the Steam setting  
and set the Steam Control Knob to the highest steam setting.  
8. When the thermostat light has gone off, keep the iron in the vertical position  
and press the Steam/Spray button to produce a strong steam jet. See  
illustration below. To prevent water leaking from the soleplate, do not keep  
the burst of steam button depressed fore more than 5 seconds.  
1. Make sure that the iron is unplugged from the power source.  
2. Set the steam control knob to no steam.  
3. Fill the iron with water following the instructions for filling on page 3.  
4. Plug the power cord into the electrical outlet.  
5. Set the temperature control dial within the steam area, I.e. “• • • ”.  
(See page 4 for setting the temperature.)  
6. The thermostat light will go “On”.  
7. When the correct temperature has been reached, the thermostat  
light will go “Off”.  
8. Now Turn the Spray/Burst of Steam button to the Steam setting  
and set the Steam Control Knob to “ON”.  
See illustration below.  
Burst of Steam  
Vertical Steam  
Please note: For maximum steam, the temperature control dial should  
be set at “• • • “ and the Steam Control set to the steam setting.  
IMPORTANT: If the iron has not been set to the correct temperature setting  
for steam, water drops may leak from the soleplate.  
5
6
 

Conair Hair Clippers IB 9 344 User Manual
Conair Scale WW31 User Manual
Coustic Car Amplifier AMP 801DB User Manual
Craftsman Chipper 247797852 User Manual
Craftsman Log Splitter 4862454 User Manual
Cypress Computer Hardware CY62148EV30 User Manual
Fisher Paykel Ventilation Hood 88833 EC120DXV2 User Manual
Fisher Price Motorized Toy Car 73517 User Manual
Fisher Price Tent V6892 User Manual
Gigabyte Network Card GA 8I945PLGE RH User Manual